- #FIAT ECU SCAN SOFTWARE FULL VERSION#
- #FIAT ECU SCAN SOFTWARE SERIAL#
- #FIAT ECU SCAN SOFTWARE SOFTWARE#
- #FIAT ECU SCAN SOFTWARE PC#
My advise is that you can buy a KKL VagCom 409.1 interface and you have 3 possibilities:ġ soldering together the pins 1, 3, 7, 9 and 12Ģ soldering all that pins thrue a 27 Ohm rezistorsįor Can or for some ECUs you need an ELM327 where you don't need a switch, you can soldering pins 1,7,9 and 12 together with or without 27 Ohm rezistor. The multiplexor means that pins 3,7,8 and12 are soldering together thrue 27 Ohm resistors.įor FES if have one of this tool you can use it if bibkare said that, I trust in him. Opel Tech 2 has a (passive) multiplexor and if bibkare said that it work it works becasue it is a KKL interface. It works just on USB not virtual com port. OP-COM it is just for OPel/SAAb and read DTC to Chevrolet ( not to all) - This one dosen't work. Ok but I told you or maybe it was a missunderstanding in my post.
#FIAT ECU SCAN SOFTWARE SERIAL#
Only draw back is that new laptops are without serial port I tested chinese opel tech2 interface that is in fact kkl multiplexed with max232, just took one wire from pin 12 and solder it directly to pin 1 for ABS, works very good, no need for any switching, much better than Blue cable USB KL, 'cause of serial connection i presume. With normal KKL i need to solder all to PIN7 but i want it this way with a multiplexer if its possible and someone have tested it like Mr. So its not nessesary to switch the Pins because the interface take the PIN which is needed for the system. My question was if there is a difference or if both are Multiplexer the OP-COM and the OpelTech2 Look in my post there are 2 different Opel Interfaces. Opel Tech2 has pins: 3,7,8,and 12 and to change it for FES you need to cgange pin 8 with 9 and put a new conection ( soldering) pin 1 with 7 between a 27 Ohm resistor ( like how is made the multiplexor into the OpelTech2 interface). Op-COm will never work for sure and OpelTech2 it is a KKL interface and you have to change the pins. M8 you talking about Op-COm interface or you're talking about OpelTech2 (chinese). ( on ebay VagCom is about 14$ and ELM327 is abou 25$)Ĭould you clarify a little bit that incident when our forum coleague burned original elm327, did he burned it beyond repairing or was it some minor break (some transistors or stabilizer), i hope that he didn't scorch the PIC.
![fiat ecu scan software fiat ecu scan software](https://www.car-auto-repair.com/wp-content/uploads/2019/11/Multiecuscan-Injector-IMA-Coding-for-Fiat-Grande-Punto-1.3-Multijet-1.jpg)
I know a mate from our forum who spend a lot of money for an interface with original ELM327 v1.4 inside and he burned in few week and I'm wondering for what? Skapang elm327 interface is about 108 UK pounds. In conclusion VagCom 409.1 and ELM327 v1.3a chinese ones are cheap and good and you can buy them from, so why you need to spend a lot of your money for a baby tool, just because they said that it has "original ELM327" inside and much more of this ELMScan is pretty old tool. I had an ELM327 v1.3a chinese one before and that one was great as well. I'm useing an ELM327 v1.4 chinese one and it works like a charm. If it can work on 34800 bauds it's ok, but I don't think so. I think it has a elm v1.2 inside, so if it can work just on 9600 bouds.
#FIAT ECU SCAN SOFTWARE SOFTWARE#
The coloured adaptor cables are only intended for use with the Fiat ECU Scan software, on supported Fiat group vehicles listed as requiring them on the FiatECUScan Supported Vehicles List.Use on other vehicles or with other software is not supported and may cause damage to your vehicle or equipment.Fes working with VAgCom 409.1 interface and with ELM327 v1.3+.ĮLMScan 5.
#FIAT ECU SCAN SOFTWARE FULL VERSION#
It can be used with the free version, or full version licenses are available separately.
![fiat ecu scan software fiat ecu scan software](https://www.multiecuscan.net/images/FESm02s.jpg)
Please Note this bundle does NOT include the Fiat ECU Scan software license. Not only do you get the 2 hardware interfaces required for full software coverage, but we include specific break-out adaptor cables for supported Airbag, ABS, Power Steering and CAN systems, so there's no need to modify your interfaces.
![fiat ecu scan software fiat ecu scan software](https://i.ytimg.com/vi/NMvnKlm98Zo/maxresdefault.jpg)
Hardware only bundle for FiatECUScan software, compatible fully with Fiat ECU Scan.Īll the hardware required to use the excellent Fiat ECU Scan software for Fiat, Alfa Romeo and Lancia vehicles - for use with the free shareware version of the software, or if you already have a full version software license.
#FIAT ECU SCAN SOFTWARE PC#
there's no need to modify your interfaces.ģ.A laptop or PC running Windows XP, Vista or Windows 7 with a USB portįiat ECU Scan Software (Free or Licensed Version)Ĭompatible Vehicle - see Fiat ECUScan's Supported Vehicles listĪ laptop or PC running Windows XP, Vista or Windows 7 with a USB port 1.Hardware only bundle for Fiat ECU Scan software,compatible fully with fiateucscan.Ģ.